I'm trying to set up a WRF/HYSPLIT simulation through READY. My first simulation ran successfully (a month or two ago) but when I tried a new setup with the same parameters except altering the release date to be 1 day earlier, I get an error at the very end of the simulation. Here are the last few lines from the model status file:
===run post-processing===
Finished in-line WRF/HYSPLIT simulation for job 290.
The model is now complete.
Fri Oct 15 11:42:45 EDT 2021
******************************************************************************
The model has crashed. Check the HYSPLIT Message file for further information.
******************************************************************************
cp: cannot stat 'hys-out/print.rsl.inline': No such file or directory
cp: cannot stat 'hys-out/CONTROL': No such file or directory
cat: CONTROL.290.txt: No such file or directory
The full status file is attached. No other files were created during the run. Is this caused by a problem in my setup, or is this a problem with READY?
Inline WRF-HYSPLIT
-
- Posts: 1
- Joined: October 15th, 2021, 12:15 pm
- Registered HYSPLIT User: Yes
Inline WRF-HYSPLIT
Post by emilygordon »
- Attachments
-
- progress_WRF_Inline_290.txt
- (24.75 KiB) Downloaded 30535 times
Return to “HYSPLIT on the READY Server”
Jump to
- HYSPLIT
- ↳ Users
- ↳ Developers
- ↳ Bugs
- ↳ Announce
- ↳ General Comments
- ↳ Trajectory Model
- ↳ Dispersion Model
- ↳ User Applications
- ↳ In-line WRF-HYSPLIT coupling
- HYSPLIT Platform Specific
- ↳ HYSPLIT for PCs
- ↳ HYSPLIT for Mac OS X
- ↳ HYSPLIT for LINUX
- ↳ HYSPLIT on the READY Server
- Meteorological Data
- ↳ General questions on meteorological data needed for HYSPLIT
- ↳ Conversion programs
- ↳ Repositories of HYSPLIT formatted data
- ↳ MeteoInfo Software
- HYSPLIT Research
- ↳ Volcanic Ash
- ↳ Wildfire Smoke
- ↳ Dust
- ↳ Chemicals
- ↳ Radiological
- ↳ Cluster Analysis
- HYSPLIT Workshop
- ↳ 2022 HYSPLIT Workshop Questions
- ↳ 1. Installing HYSPLIT
- ↳ 2. Testing the installation
- ↳ 3. Gridded meteorological data files
- ↳ 4. Trajectory calculations
- ↳ 5. Trajectory options
- ↳ 6. Trajectory statistics
- ↳ 7. Air concentration calculations
- ↳ 8. Configuring the CAPTEX simulation
- ↳ 9. Air concentration parameter sensitivity
- ↳ 10. Alternate display options
- ↳ 11. Pollutant transformations and deposition
- ↳ 12. Air concentration uncertainty
- ↳ 13. Source attribution methods
- ↳ 14. Wildfire smoke and dust storms
- ↳ 15. Radioactive pollutants and dose
- ↳ 16. Volcanic eruptions with gravitational settling
- ↳ 17. Custom simulations
- ↳ 2021 HYSPLIT Workshop Questions
- ↳ 1. Installing HYSPLIT
- ↳ 2. Testing the installation
- ↳ 3. Gridded meteorological data files
- ↳ 4. Trajectory calculations
- ↳ 5. Trajectory options
- ↳ 6. Trajectory statistics
- ↳ 7. Air concentration calculations
- ↳ 8. Configuring the CAPTEX simulation
- ↳ 9. Air concentration parameter sensitivity
- ↳ 10. Alternate display options
- ↳ 11. Pollutant transformations and deposition
- ↳ 12. Air concentration uncertainty
- ↳ 13. Source attribution methods
- ↳ 14. Wildfire smoke and dust storms
- ↳ 15. Radioactive pollutants and dose
- ↳ 16. Volcanic eruptions with gravitational settling
- ↳ 17. Custom simulations
- ↳ 2020 HYSPLIT Workshop Questions
- ↳ 1. Installing HYSPLIT
- ↳ 2. Testing the installation
- ↳ 3. Gridded meteorological data files
- ↳ 4. Trajectory calculations
- ↳ 5. Trajectory options
- ↳ 6. Trajectory statistics
- ↳ 7. Air concentration calculations
- ↳ 8. Configuring the CAPTEX simulation
- ↳ 9. Air concentration parameter sensitivity
- ↳ 10. Alternate display options
- ↳ 11. Pollutant transformations and deposition
- ↳ 12. Air concentration uncertainty
- ↳ 13. Source attribution methods
- ↳ 14. Wildfire smoke and dust storms
- ↳ 15. Radioactive pollutants and dose
- ↳ 16. Volcanic eruptions with gravitational settling
- ↳ 17. Custom simulations
- ↳ 2019 HYSPLIT Workshop Questions