[Note that the question and the answer below are recreated from a HYSPLIT FAQ site that predates this forum site. The original posting date is unknown.]
Although it appears you have deposition where there is no air concentration, this cannot be the case. If you look at the minimum air concentration for the plots, you will see that it is much smaller than the minimum contour shown. Normally the concentration plotting program automatically scales the contour interval and these smaller contours would have been shown. However, due to the popularity of the concentration animations, we set the default plot to fix the contours, so that the same color would represent the same concentration with each frame. Therefore on subsequent frames the air concentration plume appears to dissapear while deposition continues to occur. You can change this default to have the contours change from plot to plot.
Roland Draxler
I found a case where there are deposition contours where there are no corresponding air concentration contours. Why?
Topics about the HYSPLIT dispersion model.
-
- Posts: 360
- Joined: May 8th, 2019, 1:31 pm
- Registered HYSPLIT User: Yes
Jump to
- HYSPLIT
- ↳ Users
- ↳ Developers
- ↳ Bugs
- ↳ Announce
- ↳ General Comments
- ↳ Trajectory Model
- ↳ Dispersion Model
- ↳ User Applications
- ↳ In-line WRF-HYSPLIT coupling
- HYSPLIT Platform Specific
- ↳ HYSPLIT for PCs
- ↳ HYSPLIT for Mac OS X
- ↳ HYSPLIT for LINUX
- ↳ HYSPLIT on the READY Server
- Meteorological Data
- ↳ General questions on meteorological data needed for HYSPLIT
- ↳ Conversion programs
- ↳ Repositories of HYSPLIT formatted data
- ↳ MeteoInfo Software
- HYSPLIT Research
- ↳ Volcanic Ash
- ↳ Wildfire Smoke
- ↳ Dust
- ↳ Chemicals
- ↳ Radiological
- ↳ Cluster Analysis
- HYSPLIT Workshop
- ↳ 2022 HYSPLIT Workshop Questions
- ↳ 1. Installing HYSPLIT
- ↳ 2. Testing the installation
- ↳ 3. Gridded meteorological data files
- ↳ 4. Trajectory calculations
- ↳ 5. Trajectory options
- ↳ 6. Trajectory statistics
- ↳ 7. Air concentration calculations
- ↳ 8. Configuring the CAPTEX simulation
- ↳ 9. Air concentration parameter sensitivity
- ↳ 10. Alternate display options
- ↳ 11. Pollutant transformations and deposition
- ↳ 12. Air concentration uncertainty
- ↳ 13. Source attribution methods
- ↳ 14. Wildfire smoke and dust storms
- ↳ 15. Radioactive pollutants and dose
- ↳ 16. Volcanic eruptions with gravitational settling
- ↳ 17. Custom simulations
- ↳ 2021 HYSPLIT Workshop Questions
- ↳ 1. Installing HYSPLIT
- ↳ 2. Testing the installation
- ↳ 3. Gridded meteorological data files
- ↳ 4. Trajectory calculations
- ↳ 5. Trajectory options
- ↳ 6. Trajectory statistics
- ↳ 7. Air concentration calculations
- ↳ 8. Configuring the CAPTEX simulation
- ↳ 9. Air concentration parameter sensitivity
- ↳ 10. Alternate display options
- ↳ 11. Pollutant transformations and deposition
- ↳ 12. Air concentration uncertainty
- ↳ 13. Source attribution methods
- ↳ 14. Wildfire smoke and dust storms
- ↳ 15. Radioactive pollutants and dose
- ↳ 16. Volcanic eruptions with gravitational settling
- ↳ 17. Custom simulations
- ↳ 2020 HYSPLIT Workshop Questions
- ↳ 1. Installing HYSPLIT
- ↳ 2. Testing the installation
- ↳ 3. Gridded meteorological data files
- ↳ 4. Trajectory calculations
- ↳ 5. Trajectory options
- ↳ 6. Trajectory statistics
- ↳ 7. Air concentration calculations
- ↳ 8. Configuring the CAPTEX simulation
- ↳ 9. Air concentration parameter sensitivity
- ↳ 10. Alternate display options
- ↳ 11. Pollutant transformations and deposition
- ↳ 12. Air concentration uncertainty
- ↳ 13. Source attribution methods
- ↳ 14. Wildfire smoke and dust storms
- ↳ 15. Radioactive pollutants and dose
- ↳ 16. Volcanic eruptions with gravitational settling
- ↳ 17. Custom simulations
- ↳ 2019 HYSPLIT Workshop Questions