Hello,
I am aware that HYSPLIT should generally not be used for a single site profile but I am doing a comparison and I need to run with a single site profile. My peak deposition values I am getting are very small compared to another model I ran and they are smaller by 3 orders of magnitude. I have given them the same met and source term but HYSPLIT is consistently producing smaller deposition values through out the simulation.
I am getting an issue where I am making the particles heavier but the maximum deposition seems to be maxed out and not increasing further. I have attached my CONTROL and SETUP file so you can check that I am understanding this correctly.
Is there some sort of limit that is causing this or will it depend on the rate of particle release?
Thanks,
Unusual Dry Deposition
Topics about the HYSPLIT dispersion model.
Unusual Dry Deposition
- Attachments
-
- SETUP.CFG.txt
- (72 Bytes) Downloaded 254 times
-
- CONTROL.txt
- (274 Bytes) Downloaded 261 times
-
- EMITIMES.txt
- (76 Bytes) Downloaded 252 times
Jump to
- HYSPLIT
- ↳ Users
- ↳ Developers
- ↳ Bugs
- ↳ Announce
- ↳ General Comments
- ↳ Trajectory Model
- ↳ Dispersion Model
- ↳ User Applications
- ↳ In-line WRF-HYSPLIT coupling
- HYSPLIT Platform Specific
- ↳ HYSPLIT for PCs
- ↳ HYSPLIT for Mac OS X
- ↳ HYSPLIT for LINUX
- ↳ HYSPLIT on the READY Server
- Meteorological Data
- ↳ General questions on meteorological data needed for HYSPLIT
- ↳ Conversion programs
- ↳ Repositories of HYSPLIT formatted data
- ↳ MeteoInfo Software
- HYSPLIT Research
- ↳ Volcanic Ash
- ↳ Wildfire Smoke
- ↳ Dust
- ↳ Chemicals
- ↳ Radiological
- ↳ Cluster Analysis
- HYSPLIT Workshop
- ↳ 2022 HYSPLIT Workshop Questions
- ↳ 1. Installing HYSPLIT
- ↳ 2. Testing the installation
- ↳ 3. Gridded meteorological data files
- ↳ 4. Trajectory calculations
- ↳ 5. Trajectory options
- ↳ 6. Trajectory statistics
- ↳ 7. Air concentration calculations
- ↳ 8. Configuring the CAPTEX simulation
- ↳ 9. Air concentration parameter sensitivity
- ↳ 10. Alternate display options
- ↳ 11. Pollutant transformations and deposition
- ↳ 12. Air concentration uncertainty
- ↳ 13. Source attribution methods
- ↳ 14. Wildfire smoke and dust storms
- ↳ 15. Radioactive pollutants and dose
- ↳ 16. Volcanic eruptions with gravitational settling
- ↳ 17. Custom simulations
- ↳ 2021 HYSPLIT Workshop Questions
- ↳ 1. Installing HYSPLIT
- ↳ 2. Testing the installation
- ↳ 3. Gridded meteorological data files
- ↳ 4. Trajectory calculations
- ↳ 5. Trajectory options
- ↳ 6. Trajectory statistics
- ↳ 7. Air concentration calculations
- ↳ 8. Configuring the CAPTEX simulation
- ↳ 9. Air concentration parameter sensitivity
- ↳ 10. Alternate display options
- ↳ 11. Pollutant transformations and deposition
- ↳ 12. Air concentration uncertainty
- ↳ 13. Source attribution methods
- ↳ 14. Wildfire smoke and dust storms
- ↳ 15. Radioactive pollutants and dose
- ↳ 16. Volcanic eruptions with gravitational settling
- ↳ 17. Custom simulations
- ↳ 2020 HYSPLIT Workshop Questions
- ↳ 1. Installing HYSPLIT
- ↳ 2. Testing the installation
- ↳ 3. Gridded meteorological data files
- ↳ 4. Trajectory calculations
- ↳ 5. Trajectory options
- ↳ 6. Trajectory statistics
- ↳ 7. Air concentration calculations
- ↳ 8. Configuring the CAPTEX simulation
- ↳ 9. Air concentration parameter sensitivity
- ↳ 10. Alternate display options
- ↳ 11. Pollutant transformations and deposition
- ↳ 12. Air concentration uncertainty
- ↳ 13. Source attribution methods
- ↳ 14. Wildfire smoke and dust storms
- ↳ 15. Radioactive pollutants and dose
- ↳ 16. Volcanic eruptions with gravitational settling
- ↳ 17. Custom simulations
- ↳ 2019 HYSPLIT Workshop Questions