Deposition Output Data
Posted: June 11th, 2017, 2:56 pm
Hello,
I use a registered PC GUI version of Hysplit
I am attempting to extract the deposition values from a simple simulation. I would like the data to be converted into a readable format (.csv or .txt) as I want to eventually manipulate the data. I ran a simple simulation and looked at the deposition output graphically. I then tried to convert the cdump file through concentration < utilities < convert to < ASCII. I selected single file and comma delimited options then executed conversion. The resultant txt file appears to show values for concentration at 0m and 100m but none of the deposition values. If anyone could help me with the process for extracting deposition values it would be most appreciated.
Here I have attached my setup, control, and custom wind Custom wind txt file used as meteorology input(Meteorology<Convert to ARL<lat: 44.97 lon:-92.75, select txt file of winds shown below<run convert):
17 05 05 00 00 90 5.0 1500.0 0
17 05 05 03 00 90 5.0 1500.0 0
17 05 05 06 00 90 5.0 1500.0 0
17 05 05 09 00 90 5.0 1500.0 0
17 05 05 12 00 90 5.0 1500.0 0
17 05 05 18 00 90 5.0 1500.0 0
17 05 05 21 00 90 5.0 1500.0 0
17 05 06 00 00 90 5.0 1500.0 0
17 05 06 03 00 90 5.0 1500.0 0
17 05 06 06 00 90 5.0 1500.0 0
17 05 06 09 00 90 5.0 1500.0 0
17 05 06 12 00 90 5.0 1500.0 0
17 05 06 18 00 90 5.0 1500.0 0
17 05 06 21 00 90 5.0 1500.0 0
17 05 07 00 00 90 5.0 1500.0 0
17 05 07 03 00 90 5.0 1500.0 0
17 05 07 06 00 90 5.0 1500.0 0
17 05 07 09 00 90 5.0 1500.0 0
17 05 07 12 00 90 5.0 1500.0 0
17 05 07 18 00 90 5.0 1500.0 0
17 05 07 21 00 90 5.0 1500.0 0
17 05 08 00 00 90 5.0 1500.0 0
Thanks in advance!
I use a registered PC GUI version of Hysplit
I am attempting to extract the deposition values from a simple simulation. I would like the data to be converted into a readable format (.csv or .txt) as I want to eventually manipulate the data. I ran a simple simulation and looked at the deposition output graphically. I then tried to convert the cdump file through concentration < utilities < convert to < ASCII. I selected single file and comma delimited options then executed conversion. The resultant txt file appears to show values for concentration at 0m and 100m but none of the deposition values. If anyone could help me with the process for extracting deposition values it would be most appreciated.
Here I have attached my setup, control, and custom wind Custom wind txt file used as meteorology input(Meteorology<Convert to ARL<lat: 44.97 lon:-92.75, select txt file of winds shown below<run convert):
17 05 05 00 00 90 5.0 1500.0 0
17 05 05 03 00 90 5.0 1500.0 0
17 05 05 06 00 90 5.0 1500.0 0
17 05 05 09 00 90 5.0 1500.0 0
17 05 05 12 00 90 5.0 1500.0 0
17 05 05 18 00 90 5.0 1500.0 0
17 05 05 21 00 90 5.0 1500.0 0
17 05 06 00 00 90 5.0 1500.0 0
17 05 06 03 00 90 5.0 1500.0 0
17 05 06 06 00 90 5.0 1500.0 0
17 05 06 09 00 90 5.0 1500.0 0
17 05 06 12 00 90 5.0 1500.0 0
17 05 06 18 00 90 5.0 1500.0 0
17 05 06 21 00 90 5.0 1500.0 0
17 05 07 00 00 90 5.0 1500.0 0
17 05 07 03 00 90 5.0 1500.0 0
17 05 07 06 00 90 5.0 1500.0 0
17 05 07 09 00 90 5.0 1500.0 0
17 05 07 12 00 90 5.0 1500.0 0
17 05 07 18 00 90 5.0 1500.0 0
17 05 07 21 00 90 5.0 1500.0 0
17 05 08 00 00 90 5.0 1500.0 0
Thanks in advance!