concplot.ps not found

Post any questions or comments regarding the LINUX version of HYSPLIT. This includes the model execution, GUIs, results, or graphics. Be sure to mention the version of LINUX you are using.
Post Reply
kto031
Posts: 25
Joined: February 20th, 2014, 3:05 pm
Registered HYSPLIT User: Yes

concplot.ps not found

Post by kto031 » August 27th, 2015, 7:17 pm

Hi.

I have had this problem for a while, but I usually just solve it by re-installing hysplit.
But this time I can't seems to be able to run a concentration plot because the concplot.ps is not found.
Run the model is fine, but when I want to display the plot is when I get the error message.
The MESSAGE file tells me: metini - FLUXES not found in data (kg,kt) 1 1
Setting KBLS=2 to use the wind/temp profiles!
I tried setting kbls=2 but no change

Any clue to what is wrong?

Best regards,
kristine
Attachments

[The extension jpg has been deactivated and can no longer be displayed.]

[The extension jpg has been deactivated and can no longer be displayed.]


ariel.stein
Posts: 617
Joined: November 7th, 2012, 3:14 pm
Registered HYSPLIT User: Yes
Contact:

Re: concplot.ps not found

Post by ariel.stein » August 28th, 2015, 4:35 pm

The message you are getting is because the model cannot find surface flux data to calculate the dispersion parameters in your meteorological file so it will use the temperature and wind vertical profiles for that end. That should not cause any problem for you to run the model.
Are you producing any output (cdump) ? Is your run reaching 100% of completion?
If so, please reset your GUI and try again.
Also, you can open your command prompt and go to the "working" directory and type:
..\exec\concplot -icdump
check if you get a concplot.ps file.

kto031
Posts: 25
Joined: February 20th, 2014, 3:05 pm
Registered HYSPLIT User: Yes

Re: concplot.ps not found

Post by kto031 » August 28th, 2015, 11:29 pm

Yes cdump is created but its does not make sense. And yes the run is reaching 100%.
I reset the GUI and tried again with no luck.

Then I did: ./../exec/concplot -icdump in my working directory and got:

[ktofte@yslogin2 working]$ ./../exec/concplot -icdump
Started Concentration Drawing
Last Changed Rev: 770
Last Changed Date: 2015-08-27 15:26:14 -0600 (Thu, 27 Aug 2015)

All concentrations ZERO - no maps
900

Any other suggestions? :/
Attachments

[The extension jpg has been deactivated and can no longer be displayed.]


ariel.stein
Posts: 617
Joined: November 7th, 2012, 3:14 pm
Registered HYSPLIT User: Yes
Contact:

Re: concplot.ps not found

Post by ariel.stein » August 31st, 2015, 9:23 am

Can you please send me your SETUP.CFG and MESSAGE files?

kto031
Posts: 25
Joined: February 20th, 2014, 3:05 pm
Registered HYSPLIT User: Yes

Re: concplot.ps not found

Post by kto031 » August 31st, 2015, 3:50 pm

I can't find SETUP.CFG in my working directory but I have MESSAGE, CONC.CFG and the CONTROL file attached.

I appreciate your time helping me!

- Kristine
Attachments
CONTROL.txt
(313 Bytes) Downloaded 151 times
CONC_CFG.txt
(766 Bytes) Downloaded 131 times
MESSAGE.txt
(36.19 KiB) Downloaded 138 times

ariel.stein
Posts: 617
Joined: November 7th, 2012, 3:14 pm
Registered HYSPLIT User: Yes
Contact:

Re: concplot.ps not found

Post by ariel.stein » September 1st, 2015, 10:05 am

Your problem is in the control file:
10 05 01 06
2
19.4100 -155.2864 1747.0
19.3864 -155.1050 1198.0
48
0
10000.0
1
/glade/scratch/ktofte/HIGHSPLIT/hysplit/trunk/working/
ERA_kona2
1
SO2
40.0
48.0
10 05 01 06 00
1
0.0 0.0
0.05 0.05
30.0 30.0
./
cdump
1
100
10 05 01 06 00
10 05 02 06 00 =====> end concentration calculation time
00 48 00 ========> asking for a 48 hour output
1
0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
0.0
0.0

You have to either change your ending time for the concentration calculation to 10 05 03 06 00 or change your averaging time to 00 24 00.

kto031
Posts: 25
Joined: February 20th, 2014, 3:05 pm
Registered HYSPLIT User: Yes

Re: concplot.ps not found

Post by kto031 » September 1st, 2015, 2:44 pm

Thank you! This solved my problem.

- Kristine

Post Reply